Sunday, January 28, 2007

20 Watt Power Amplifier (IC)



There are many instances where a simple and reliable power amplifier is needed - rear and centre

channel speakers for surround-sound, beefing up the PC speakers, low powered tweeter amplifier, etc. For those who want to build their own 'Gainclone' amplifier, this will certainly do the job :-)

This project (unlike most of the others, but in a similar vein to Project 19) is based almost directly on the typical application circuit in the National Semiconductor specification sheet. You can also use the TDA3050 (from SGS-Thompson), which has almost identical performance and (remarkably) the same pinouts! As it turns out, the amp in the NS application circuit is pretty good, as is the (very similar) one from SGS. The amp is also remarkably simple to build - if you have a PCB! These ICs are a cow to wire on Veroboard - it is possible, but results are unpredictable.

From :: http://sound.westhost.com/project72.htm

16 watt amp


U1 U2LM383 8 watt audio amplifier ic
R1, R3220 ohm resistor
R2, R42.2 ohm resistor
R51 megohm resistor
R6100k audio taper potentiometer
C1, C710uf electrolytic capacitor
C2, C5470uf electrolytic capacitor
C3, C4, C60.2uf ceramic capacitor
SPKR14 to 8 ohm speaker (up to 8 inches diameter)


all resistors are 5 or 10 percent tolerance, 1/4-watt
all capacitors are 10 percent tolerance,
rated 35 volts or higher
this circuit provides 16 watts of amplification. it is built using two LM383 power audio amplifiers. use suitable heat sinks with the ic's.

50 Watt Amplifier



This is a handy, easy to build general purpose 50 watt amp. The amp has an input for a radio, TV, stereo or other line level device. It also has a phono input for a record player, guitar, microphone or other un-amplified source. With the addition of a low pass filter at the input, it makes a great amp for a small subwoofer.

Part
Total Qty.
Description
Substitutions
R11200 Ohm 1/4 W Resistor
R21200K 1/4 W Resistor
R3130K 1/4 W Resistor
R511K 1/4 W Resistor
R615K 1/4 W Resistor
R7,R1021 Meg (5%) 1/2 W Resistor
R8,R920.4 Ohm 5 W Resistor
R11110K Pot
R12,R13251K 1/4 W Resistor
R14147K 1/4 W Resistor
C11100uF 35V Electrolytic Capacitor
C210.011uF Capacitor
C313750pF Capacitor
C4,C621000pF Capacitor
C5,C7,C830.001uF Capacitor
C9150pF Capacitor
C1010.3uF Capacitor
C11,C12210,000uF 50V Electrolytic Capacitor
U1,U22741 Op Amp
U31ICL8063 Audio Amp Transister Driver thingy
Q112N3055 NPN Power Transistor
Q212N3791 PNP Power Transistor
BR11250 V 6 Amp Bridge Rectifier
T1150V Center Tapped 5 Amp Transformer
S11SPST 3 Amp Switch
S21DPDT Switch
F112 Amp Fuse
SPKR118 Ohm 50W Speaker
MISC1Case, Knobs, Line Cord, Binding Posts Or Phono Plugs (For Input And Output), Heatsinks For Q1 And Q2


From :: http://www.aaroncake.net/circuits/amp50w.htm

4-WATT AF AMPLIFER



The circuit is very simple and incorporates darlington output transistors that will provide more than enough output current than is needed to drive a 3-ohm speaker. The gain may be pre-set for a variety of input levels, making it suitable for amplifying computer and cassette-deck Line-output levels. The input level is also suitable for use with the TDA7000 receiver. All components are easily available and I will shortly be making this project available as a kit. Naturally, the project will be built on a PCB which will also be available separately. Here is the first PCB, assembled and working.

From :: http://web.telia.com/~u85920178/use/afamp-4w.htm

20 Watt Power Amplifier


This IC chip was designed specifically for use in power boosting applications in automobiles. It is self protecting against short circuits and thermal problems. In the bridge configuration shown it will deliver 20 watts of power into a 2 ohm speaker operating at 14.4 volts.

From :: http://home.maine.rr.com/randylinscott/may98.htm